Metric DIN 444 Eye Bolts are bolts with an eye (loop/ring) at one end and a threaded shank at the other. They are threaded into a pre-tapped hole or secured with a nut to a structure so that a rope or cable can be attached to the loop end. Only eye bolts with shoulders should be used to support angular loads.

Crosby® S-279 Machinery Eye Bolt UNC M-279 Crosby® S-279 Machinery Eye Bolt Metric Shoulder Type Eye Bolts Shoulder Type Eye Bolts *Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2 times the Working Load Limit. **On Request: Special threading or as forged bolts for customer conversion. •Forged Steel - Quenched

IMPORTANT — Read and understand these instructions before using eye bolts. Regular Nut & Shoulder Nut Eye Bolt – Installation for In-line Loading. • Always 

See Detail. M16 Z/P Lifting eye bolt C15E Din 580 5200pcs. 2021-08-03 15:20:38. Ireland. See Detail. Din 580 A4 m64 x 6.0.

The dimensions are for your approximate guidance only and manufacturer may not be necessary adhere to above specifications. Other threads can also be supplied 

The above eye bolts comply to British Standards as follows: Short Shank code WIR15112 to BS 4278 Part 1 1984. [The scope of this standard starts at M12 - the M10 is machined from an M12 forging].

ORDERING EYE BOLTS Suncor offers standard stainless steel eye bolts with thread sizes ranging from 3/16" to 1" and thread lengths from 0.53" to 18". If you require an eye bolt that does not fall into these dimensions, refer to the "Custom" section below. Standard Eye Bolt Features

1.1.1 This standard covers only eyebolts with eyes of internal diameters capable of permitting direct engagement with eyehooks of the same lifting capacity ( working load limit ) for use with Grade T ( 8 ) chain. 2020. 9. 28. · Our these Lifting Eye Bolts are strong and robust, and correspond to standard JIS1168.

Title of Legally Binding Document: Specification for Eye Bolts with Collars Number of Amendments: Equivalence: Superceding: Superceded by: LEGALLY BINDING DOCUMENT Step Out From the Old to the New--Jawaharlal Nehru Invent a new India using knowledge.--Satyanarayan Gangaram Pitroda

Eye Bolt under 12mm is not suggested to use for lifting purposes ,refer to relevant standards. 8. Eye Bolts should always be used in accordance with 

Lifting eye bolts according to the present Standard shall be manufactured solely fron C 15 steel according to DI! 17210. They must be nomalized and possess a notched bar Impact strength of 80 m/cn (ISO round notch test bar) or or 90 n/cn2 (DVM test bar). 2.2. Lifting eye bolts must be clean drop forgings.

Lifting eye bolts. BN 257. +2. DIN 580. ~ISO 3266. ~UNI 2947. ~ČSN 021369 Order now. Product data sheet (PDF). Product variants (23) 

Eye bolts and eye nuts are used for lifting machines, appliances or any please refer to the standard, DIN 580 for eye bolts or DIN 582 for eye nuts.

ORDERING EYE BOLTS Suncor offers standard stainless steel eye bolts with thread sizes ranging from 3/16" to 1" and thread lengths from 0.53" to 18". If you require an eye bolt that does not fall into these dimensions, refer to the "Custom" section below. Standard Eye Bolt Features

STANDARD SHANK LENGTHS. PLAIN & SHOULDER PATTERN. Stock Numbers. Dimensions - Inches. Plain. Shoulder. Shank. Eye. Overall Length. Plain. Overall Length.

DIN 580 Specification specifies the properties of steel and stainless steel eyebolts and provides information on their correct use in lifting operations (as part of slings and as load handling equipment). Eye bolts according to this standard can be used in a temperature range from −20 ° C to +200 ° C without any restriction of the load capacity.

as standard. When installing lifting eye bolts it is The introduced force must act in the direction of the eye bolt plane (illustration right, 

Lifting eye bolts. Steel / Stainless Steel. SPECIFICATION. Version in Steel ST. - Steel C 15 E. - Drop-forged. - Annealed. - Contact face machined.

Metric DIN 444 Eye Bolts Visit our online store for product availability Dimensions of Metric DIN 444 Eye Bolts Thread d1 M5 M6 M8 M10 M12 M16 M20 M24 (M27) M30 (M33) M36 (M39) b +2P 0.8 1 1.25 1.5 1.75 2 2.5 3 3 3.5 3.5 4 4 16 18 22 26 30 38 46 54 60 66 - - - 0 - - 28 32 36 44 52 60 66 72 78 84 90

USE ONLY SAFEPOINT & SWIVEL EYE BOLT FOR ANGLE LIFTING. SafePoint Forged Eye Bolt Specifications given are indicative and are subject to change.

Dimensions of Metric Machinery Eye Bolts with Shoulder. Print this page. Size. (A x Pitch x B) Outside Eye Diameter. (C) (mm) Inside Eye Diameter. (D)

Regular Nut Eye Bolt Shoulder Nut Eye Bolt Machinery Eye Bolt G-291 G-277 G-279 Important Safety Information— Read and Follow Inspection/Maintenance Safety: † Always inspect eye bolt before use. † Never use eye bolt that shows signs of wear or damage. † Never use eye bolt if eye or shank is bent or elongated.

Note: All Eye Bolts and Eye Nuts, whether in blanks or fully machined, as shown on page B267, are covered by our standard warranty. The warranty becomes VOID whenever modifications are made or further machining is done by the buyer, also in cases where these items are subject to an angular lift or pull. A C E S D M F N T C1035 SPECIFICATIONS IN

The bolts which are used with collars are suitable even for angular loads whereas those which do not have a shoulder are not suitable for angular loads. However, for heavy off-axis loads, an eye bolt with continuous eye and integral shoulder can be used. Be sure to restrict the axis angle to less than 45 degrees.

Machine elements. DIN 580. Lifting eyebolts. Stainless steel. STAINLESS. STEEL. INOX. RoHS. STANDARD EXECUTIONS. - DIN 580-NI: AISI 304 stainless steel.

WARNING. • Load may slip or fall if proper eye bolt assembly and lifting procedures are not used. • A falling load can seriously injure or kill.

Material Lifting eye bolts according to the present Standard shall be manufactured solely fron C 15 steel according to DI! 17210. They must be nomalized and possess a notched bar Impact strength of 80 m/cn (ISO round notch test bar) or or 90 n/cn2 (DVM test bar). 2.2. Lifting eye bolts must be clean drop forgings.

These lifting eye bolts correspond to standard sheet DIN 580. The following guidelines of lifting eye bolts DIN 580 the have to be observed in addition to the load values given in the above table. The eye bolt must be of fully screwd in to achieve a perfect contact between the two mating faces. Both threads must be of a equal length and the

Oct 30,  · Nut Eye Bolts Forged 1030 Carbon Steel Hot Galvanized** Plain Pattern. All other sizes hot galvanized. Availablemechanical galvanized upon request.All standard stock

please refer to the standard, DIN 580 for eye bolts or DIN 582 for eye nuts. It is required that the products are regularly inspected and that the 

STANDARD EXECUTIONS - DIN 580-NI: AISI 304 stainless steel. - DIN 580-A4: AISI 316 stainless steel. FEATURES AND APPLICATIONS The use of DIN 580 lifting eye bolts must take place under the following conditions: - the length of the thread of the assembly hole must be equal to the length of the thread of the pin of the eyebolt;